Paver Cleaning and Sealing: A Practical Step-by-Step Guide
Pavers make a great addition to any Shellharbour property, whether they sit in a driveway, around a pool, along a patio or in a commercial entrance. Between the salt-laden coastal air, humidity, shaded southern yards and regular rain on the Illawarra coast, pavers take a lot of punishment. Over time they collect algae, mould, oil, tannin stains and general grime. This guide walks you through how to clean and seal pavers properly in 2026, so they look good and last for decades.
Why Paver Cleaning and Sealing Matters in Shellharbour
Concrete, clay brick and natural stone pavers are all porous. That means moisture, spores, oils and dirt work their way into the surface. In coastal conditions, this leads to a few common problems:
- Algae and moss growth in shaded or damp areas, which makes surfaces slippery and unsafe.
- Efflorescence, the white powdery salt deposit that rises to the surface as moisture evaporates.
- Oil and rust stains from vehicles, outdoor furniture and garden products.
- Fading and surface wear from UV exposure and repeated harsh cleaning.
- Weed growth and joint sand loss that weakens the paved area over time.
Regular cleaning and a quality sealer protect your investment, make maintenance easier and help you avoid expensive repairs or replacement.

Step-by-Step: How to Clean Pavers
Step 1: Inspect and Prepare the Area
Start by walking over the area and looking for loose or sunken pavers, cracked units, weeds and stained patches. Remove furniture, pot plants and any loose debris. Sweep thoroughly and cover nearby garden beds, or wet them down, if you plan to use any cleaning chemicals. Check the weather too. Aim for a mild, dry day with no rain forecast for at least 24 to 48 hours, especially if you plan to seal afterwards.

Step 2: Treat Algae, Mould and Biofilm
Algae removal is a major part of paver care in our humid climate. Black, green or slimy patches are usually algae, lichen or biofilm, and simply blasting them with water often removes only the surface layer. A better approach is to apply a suitable antimicrobial or sodium hypochlorite based treatment, let it dwell for the recommended time, and then rinse. This kind of chemical sanitation pressure cleaning targets bacteria and spores at the root, which slows regrowth. Always follow the manufacturer's directions, protect plants, and prevent runoff from entering stormwater drains.
Step 3: Pressure Clean the Surface
Pressure washing is the most effective way to lift embedded dirt, but technique matters. Too much pressure or a narrow nozzle can etch the surface, strip colour or blow out the joint sand.
- Use a fan-tip nozzle or a surface cleaner attachment for even results and to avoid streaking.
- Keep the wand at a consistent distance, typically 20 to 30 centimetres from the surface.
- Work in overlapping, straight passes in the same direction.
- Choose a moderate pressure for concrete pavers and lower pressure for older, softer clay or natural stone.
The same principles apply whether you are cleaning a backyard deck area, a brick path, an asphalt driveway or a large commercial entry. Always test a small, hidden section first.
Step 4: Tackle Stubborn Stains
Different stains need different treatments:
- Oil and grease: use a degreaser or poultice and allow it to draw the oil out before rinsing.
- Rust: use a rust remover designed for masonry. Avoid mixing it with chlorine products.
- Efflorescence: use a dedicated efflorescence cleaner or a mild acid wash, applied carefully and neutralised afterwards.
- Tannin stains from leaves: these often respond to an alkaline cleaner followed by a rinse.
Step 5: Rinse, Dry and Re-Sand the Joints
Rinse the entire area thoroughly to remove all cleaning residue. Then allow the pavers to dry completely, which usually takes 24 to 48 hours depending on humidity and shade. Once dry, top up the joints with kiln-dried paving sand or a polymeric jointing sand. Sweep it in, compact lightly and brush off the excess. Properly filled joints lock the pavers together and reduce weed growth.

Step-by-Step: How to Seal Pavers
Step 6: Choose the Right Sealer
Sealers generally fall into two groups, and the right choice depends on your look and use:
- Penetrating (impregnating) sealers: soak into the paver, leave a natural matte finish and protect against moisture and stains. They suit pool surrounds and high-traffic areas where slip resistance matters.
- Film-forming (acrylic or solvent/water-based) sealers: sit on the surface, enhance colour and give a wet-look or satin finish. They offer strong stain protection but can become slippery when wet if the wrong product is used.
For outdoor areas in Shellharbour, look for sealers with UV resistance and good breathability so moisture can escape. Check that the product suits your specific paver type, and consider an anti-slip additive for areas that get wet.
Step 7: Apply the Sealer
- Confirm the pavers and joints are completely dry and the temperature is within the product's recommended range, usually between 15 and 30 degrees Celsius.
- Mask off edges, walls, garage doors and garden borders.
- Apply the first coat evenly with a roller, low-pressure sprayer or brush, working in manageable sections and maintaining a wet edge.
- Avoid pooling, as this can cause blotchy or glossy patches.
- Apply a second thin coat if recommended, once the first has dried to the manufacturer's specification.
- Keep foot traffic off for at least 24 hours and vehicles off for 48 to 72 hours, or as directed on the label.
How Often Should You Clean and Seal?
As a general guide, most residential pavers benefit from a clean every 12 months, and sooner in damp, shady or tree-covered spots. Sealing typically lasts two to five years depending on the product, sun exposure and traffic. If water no longer beads on the surface, it is probably time to reseal. Commercial properties with heavy foot traffic, such as cafes, retail centres and apartment https://donovanoyto041.solsticebrief.com/posts/schedule-a-commercial-pressure-wash-before-selling-your-property complexes, may need more frequent cleaning to keep the area safe and presentable.
Cleaning Other Outdoor Surfaces at the Same Time
If you are already setting up for paver work, it often makes sense to look at the rest of the property. Algae and grime rarely stay confined to the ground. Consider whether any of these also need attention:
- Roofs: algae and lichen shorten roof life. Soft washing and certified roof cleaning is gentler than high-pressure blasting on tiles and Colorbond.
- Gutters: clogged gutter cleaning prevents overflow and water damage. Aluminium gutters in particular benefit from regular clearing and algae removal.
- House exteriors: house washing removes mould and staining from brick, render and cladding.
- Solar panels: clean solar panels, including bird dropping removal, help maintain output.
- Decks and driveways: a clean deck and a clean driveway improve safety and appearance.
Commercial Paver and Exterior Cleaning
Business owners in Shellharbour have additional factors to consider, including public safety, brand presentation and compliance with workplace and environmental obligations. Commercial pressure washing for car parks, footpaths, building facades, courtyards and shopfront paving removes slip hazards, chewing gum, oil stains and biofilm. Commercial exterior cleaning programs are often scheduled outside trading hours, and may include roof cleaning, gutter cleaning, facade cleaning and sanitation washing as part of a single maintenance plan.
Specialised surfaces such as asphalt driveways, acrylic tennis courts and clay tennis courts need a different approach to standard pavers. Acrylic surfaces need low-pressure, non-abrasive cleaning to protect the coating, while clay courts require careful treatment to avoid disturbing the playing surface. For tennis courts, algae removal and regular cleaning improve grip and player safety.
DIY or Professional Cleaning?
Many homeowners can handle a small patio with a hired pressure washer and the right products. However, a certified pressure cleaning specialist offers advantages in several situations:
- Large areas, steep driveways or hard-to-reach spaces.
- Delicate surfaces such as old clay pavers, natural stone or acrylic courts.
- Persistent stains, heavy biofilm or recurring algae.
- Commercial sites that need compliant wastewater management and minimal disruption.
- Roof, facade or solar panel work that involves working at heights.
When comparing providers, ask about insurance, equipment, chemicals used, environmental practices and what sealer products they apply. Affordable pressure washing does not have to mean cutting corners, so look for clear quotes that explain exactly what is included.
Common Mistakes to Avoid
- Using too much pressure, which scars the surface and removes joint sand.
- Sealing damp pavers, which can trap moisture and cause a cloudy or white appearance.
- Applying too much sealer, leading to sticky, glossy or peeling patches.
- Skipping the joint sand, which allows movement and weed growth.
- Ignoring drainage, as standing water speeds up algae and staining.
Ongoing Maintenance Tips
Between full cleans, sweep regularly, clear leaves quickly, and wash off spills as soon as they happen. Trim back overhanging vegetation to improve sunlight and airflow, and check that downpipes and gutters are not overflowing onto paved areas. A light rinse and a low-pressure algae treatment every few months can keep problem areas under control and extend the time between full cleans.
Final Thoughts
Cleaning and sealing pavers is one of the most effective ways to protect your outdoor space from Shellharbour's coastal conditions. With careful preparation, the right cleaning method, thorough drying and a suitable sealer, you can restore the look of your paving and keep it performing well into 2027 and beyond. If the job feels too big, or you also have roofs, gutters, facades, solar panels or commercial surfaces that need attention, a local certified pressure cleaning professional can provide a tailored solution for your property.
Shellharbour Pressure Cleaning Pros
Shellharbour Rd, Warilla NSW 2528, Australia
(02) 4210 5306